Approval of Change Order #3 – Tricon Construction Group – Water Treatment Facility Upgrade — E-3

GENERAL INFORMATION Standard Warranty Mesker Door™ Inc. warrants for a period of one (1) year from date of shipment, all material manufactured by us to be free from defects in material and workmanship under normal use and service. All such material is supplied subject to this warranty. The company’s obligation there under is limited to repairing or replacing at its option any such material which, upon examination is found to have been defective. This warranty is expressly in lieu of all other warranties expressed or implied, and of all obligations or liabilities on its part for damages, including but not limited to consequential damages. No agent is authorized to assume for it any liability except as set forth above. Nor does Mesker Door™ Company assume any liability for modifications performed on materials after said materials leave Mesker’s factory. EDGEWATER DOOR warrants all its doors and frames set forth herein to be of good material and workmanship and to be free of defects which would render said doors or frames unserviceable or unfit for their ordinary, recommended use for the designated time, except as otherwise set forth in this warranty. EDGEWATER DOOR shall have no liability under this warranty or under any implied warranties unless such doors and frames have been handled, stored, finished, installed, and maintained in accordance with “HANDLING, JOB FINISHING AND INSTALLATION INSTRUCTIONS.” Any claims in connection with our warranty must be submitted in writing upon site survey. All doors and frames must be inspected prior to installation, and installation of all field finished doors and frames shall constitute acceptance of the factory finish. Any EDGEWATER DOOR produced doors or frames claimed to be defective within the meaning of this warranty, MUST BE CHECKED BY AN AUTHORIZED REPRESENTATIVE OF THE COMPANY. If a claim for defective merchandise is found to be valid within the meaning of this warranty, EDGEWATER DOOR will either (1) repair or (2) replace with an identical unit, at no cost around the purchase price, at the option of EDGEWATER DOOR. No liability whatsoever shall be attached until the product involved has been paid for in full. WARRANTY PERIOD Doors and frames are guaranteed for the life of the product against corrosion induced failure and for a period of ten (10) calendar years after the date of purchase against defects. Factory finishes are only warranted for a period of (1) one year. All time periods commence as of factory ship date. CONDITIONS AND EXCEPTIONS Under no circumstances will EDGEWATER DOOR be liable for the following: (a) Failures not reported within the applicable warranty period; (b) Failures due directly or indirectly to abnormal conditions, negligence, abuse or improper installation; (c) Losses, costs, expenses, liabilities, and damages, including but without limitation to, loss of profit, property damage to third parties or property, and any other special or consequential damages, whether direct or indirect. LIMITED DOOR AND FRAME WARRANTY TOLERANCES 1. Size tolerance: thickness ± 1/16"; length ± 1/8"; widths ± 1/16". 2. Squareness tolerance: diagonal measurement difference shall not exceed 3/8". 3. Factory hardware preparation tolerance: ± 1/16" tolerance will be allowed on all hardware preps. 4. Stile, rail, and core show-through (telegraphing) on doors and frames shall not be considered a defect unless the faces vary from a true plane more than .010" of an inch in any 3" span. 5. Warp shall not be considered a defect unless it exceeds 1/4" in the plane of the door itself when measured in a section not exceeding 3-6 x7-0. "Warp" is any distortion in the door itself and does not refer to the relationship of the stiles, rails, or core to each other or to the hung. The term "warp" shall include bow, cup, and twist. In measuring the amount of warp present in a door, the following method shall be used. The straight edge, taut wire, or string shall be placed along the face of the door at any angle (i.e., horizontally, vertically, or diagonal) with the door in its installed position. The measurement of the bow, cup and twist shall be made at the point of maximum distance between the bottom of the straight edge, taut wire or string and the face of the door. 6. Thermal bow and expansion may occur when opposing sides of a door are exposed to extreme temperature or climate conditions. Typical examples are: A. Doors with direct exposure to the sun. Light colored finishes are recommended as opposed to dark finishes which increase the possibility of bow or expansion. B. Exterior doors opening to or from heated spaces in northern climates. Thermal bow and/or expansion is a temporary condition and not a defect therefore not subject to the measurement for warp. ADDITIONAL EXCLUSIONS: 1. There is no warranty for the appearance of field finished doors and frames.